Save to shopping list
Create a new shopping list

STC-1000 Thermostat 230V Temperature Controller with Sensor

STC-1000 Thermostat 230V Temperature Controller with Sensor
STC-1000 Thermostat 230V Temperature Controller with Sensor
STC-1000 Thermostat 230V Temperature Controller with Sensor
STC-1000 Thermostat 230V Temperature Controller with Sensor
Our bestseller
Supply Voltage:
14,95 €
/ pc
Easy return of this product within 14 days from the date of purchase for any reason
This product is not available for collection

STC-1000 - it is a very popular thermostat, small size temperature controller, which we can use to automatically control cooling and heating. It has a readable LED display and a waterproof temperature sensor with a 1m cable. The device can be used in refrigerators, stoves, pumps, swimming pools, smokehouses, wherever you need to control the temperature.

Technical data:
- Power supply: 220V / 230V AC
- Measurement accuracy: ± 1 ° C
- Measurement temperature range: -50 + 110 ° C
- External dimensions of the device [width x height x depth]: 75 x 35 x 85 [mm]
- Sensor: hermetic, stainless steel cylinder Ø4mm x 20mm, type NTC
- Sensor length 1m
- Power consumption: <3W
- Relays: 10A / 240V AC
- Housing material: flame-retardant ABS
- Weight: 104g
- LED screen dimensions: 20 x 43 [mm]

Modes of operation:
F1 - Temperature setting
F2 - Hysteresis: 0.3 ° V - 10 ° C
F3 - Relay activation delay time (LED blinking) - from 1 to 10 min.
F4 - Temperature sensor calibration: (-10 ° C - 10 ° C)
When the temperature exceeds the set temperature (F1 + F2), cooling is turned on, and when it drops, heating is turned on.

User manual:

Checking parameters:
During normal operation, press the ▲ button once. The set temperature will be displayed. Pressing the ▼ button once will display the set hysteresis.

Parameter setting:
During normal operation, hold down the "S" button for approximately 3 seconds. The temperature setting mode will be activated and the display will show “F1”, the SET LED will be lit. Use the arrows to go to the next setting items, which will be described in the table below. To change the value of the required setting, select the appropriate item, then while holding the "S" button, change the setting value using the ▲ or ▼ button. After the set value is set, release the "S" button and press the power button once. This will save the set values ​​and return to the current temperature display mode. If, after entering the setting mode, no operation is performed within 10 seconds, the device will automatically return to the normal operation mode. If an error occurs while saving the parameters (the display shows "Er"), the controller will return to the normal operation mode within 3 seconds.

Factory reset:
In the event of an error, the display will show "Er". Pressing any button at this time will restore the default settings and return to the normal operating mode.

Product code
GL.000.270
Supply Voltage
230 V AC
Your previous questions regarding this product
Ref STC-1000 Summary of Question - is it OK to place a heating load (within spec of course) on one output and NO LOAD on the other output, though set temperatures as if there were a hot and cold load to be switched at two temperatures, Detail on question - I understand that typically one of the outputs might be used to turn on/off a heater, the other of the two outputs to turn on/off a cooler. I may need that facility long term. Short term though, I just want to set the temperature so that a heater approx 100w (0.1KW) is turned on at around say 25DegC. I don't intend to use a cooling source or any other load at the second output.) So, I am assuming that I can set the heating to come on at 25DegC and although there is no load there to set the secondary output at say 20DegC so that the temperature stays around the 20/25DegC mark

Hi Charles,

connecting load to either of the outputs is not mandatory.

The controller relays work simply as switches breaking your circuit. You can use just the heating channel and ignore the cooling one. The controller doesn't care whether there is anything connected to its outputs. It will activate a relevant relay anyway once the preset conditions are met.

Mind that cooling channel works in contrary to the heating one, i.e. it will activate its relay when temperature goes ABOVE the set value while heater will be turned on when temperature goes BELOW its channel setting.

Do you need help? Do you have any questions?
Use the inquiry form or call the number+353 89 248 3168
Ask a question
Ask us a question about this product
If our description is not sufficient, please send us your questions about this product. We will reply as soon as possible. Data is processed in accordance with privacy policy. By submitting data, you accept our privacy policy.
Share your opinion with us and the others
Your opinion:
5/5
Add your own product photo:
pixelpixel